1.

Introduction

The retrieval of forest above-ground biomass (AGB, or biomass hereafter) using remote sensing data has received increasing attention in the last decades for several reasons: primarily, for the ability of remote sensing to spatially extrapolate point field information on forest parameters, enabling AGB mapping over large areas; for the increased availability of different Earth Observation data types; and, in a global scenario of climate change and biodiversity loss, for the relevance of forest biomass with respect to global carbon accounting and reporting, conservation and management of natural resources, and environmental modeling.^1–7

Different methods have been developed to estimate AGB with remote sensing and ground data, based on passive and/or active instruments.^8–10 Active sensors, such as light detection and ranging (LIDAR) and synthetic aperture radar (SAR), have the advantage to penetrate the canopy; for this reason, they are considered the most useful tools for providing vertical structure or volumetric forest measures.^11,12

In the last decades, different new SAR missions have been developed with improved features, such as polarimetric capabilities, enhanced spatial resolution, and increased revisiting time. New missions are also planned for the near future,¹³ with a consistent increase in SAR data types available to scientific and user communities. This data availability calls for a better understanding of the utility of new SAR information in ecological research.

SAR sensors provide information on the backscattered energy from the illuminated target. Depending on the structural and dielectric characteristics of forest canopies, the relative contribution of volume, surface–volume interactions, and surface scattering from forest in the total backscatter signal of an imaging radar can vary.^14–16 SAR sensors can have different wavelengths (bands) and thus different abilities to penetrate the forest. Moreover, they have the important advantage of being insensitive to cloud coverage and, when mounted on satellites, to cover large areas with repeated measures. As evidenced by different models, P- and L-bands provide stronger backscatter from branches and trunks with respect to X- and C-bands, respectively, which collect most of the energy from leaves and needles.^17,18 In forest parameters characterization, notable results have been obtained with P- and L-bands or combining different wavelengths.^19,20 Accurate results in forest attributes assessment have been obtained using SAR interferometry and polarimetric interferometry techniques,^21–24 even if the scarce availability of interferometric couples collected in short time intervals, together with the high expertise required for the application of these methods, limits their use in operational forest monitoring.

Forest characterization has also been successfully carried out using C- or X-bands,²⁵ especially when dense temporal series are used.^26,27 In fact, these wavelengths are more sensitive to surface moisture.^28,29 In this case, a multitemporal approach can reduce the signal variability; in addition, the availability of SAR data from different dates allows the selection of those periods and scenes having stronger sensitivity of the backscatter to the target.³⁰

SAR and other data types (e.g., LIDAR) can also be used in conjunction for forest research. The fusion of SAR and LIDAR has been attempted to improve SAR-based prediction, and it can be promising for large area efforts; a review showed that the main advantage is in the use of an accurate LIDAR digital elevation model for SAR-based AGB prediction or in the upscale of local LIDAR metrics to large areas with SAR data.³¹ Combining SAR and optical data has brought accurate AGB predictions in a number of cases because the structural SAR information can be complemented with canopy density, forest type, and foliage-related information collected by optical instruments.^32–36

Even with the increase in new data, fusion techniques, and innovative researches, AGB prediction based on SAR remains a challenging task, as saturation of the signal is common in forests,³⁷ where the backscatter is influenced by several factors, such as the soil moisture, especially when the vegetation coverage is low;³⁸ the forest type, the leaf presence with needleleaf forests possibly having the highest saturation level;³⁹ the seasonal and weather conditions;⁴⁰ the canopy roughness;⁴¹ and the SAR signal polarization as well as the incidence angle.⁴² Therefore, studies clarifying SAR response in different conditions and forests types are important, as they can support the effective exploitation of new SAR data streams into ecological research and monitoring.

The launch of the first Sentinel satellite (S1A: C-band SAR) by the European Space Agency (ESA) in 2014, followed by the S1B having the same characteristics as the first, now allows very frequent SAR data acquisitions. The subsequent launch of the Sentinel-2 satellites in 2015 and 2017 (S2A and S2B: enhanced multispectral sensors), together with a policy of free data, has strongly broadened the opportunities for forest monitoring. These new ESA data add to the growing archives of multispectral Landsat and ALOS SAR L-band SAR data.

The development of new perspectives and methods is illustrated by recent research, exploiting the potential of Sentinels data for forest characterization, such as new methods for forest deforestation, degradation, and fire monitoring;^43,44 new detailing of canopy in terms of biophysical properties or for functional types classification;^45,46 and innovative data fusion for mapping plantation extent.⁴⁷ Very few studies addressed the applicability of S1, S2, or joint data, for biomass monitoring. For S2, a preliminary test was conducted by Chrysafis et al.⁴⁸ in a heterogeneous Mediterranean forest to predict growing stock (GS) volume based on S2 and Landsat 8 data, while Majasalmi and Rautiainen⁴⁵ used simulated S2 data for characterizing biophysical variables in a boreal forest. For S1, Chang and Shoshany⁴⁹ explored the potential of this data joined with S2 for biomass mapping in Mediterranean shrublands. In central Italy, where forests are fragmented and included in a highly heterogeneous landscape, fine-scale information on forest attributes is important to orient management and conservation activities. At the country level, AGB and related parameters (GSs, basal area, etc.) were mapped in a number of remote sensing-based efforts. Some research addressed the testing of new methods and data at site level,^50,51 while others covered the entire country.^52,53 These large-scale efforts were based on optical medium-resolution imagery and produced important data sources. However, some limitations in these maps were recognized,⁵³ in part due to the intrinsic features of the remote sensing and validation data used and in part due to the spatial resolution (1 km), too coarse to capture the variability of fragmented landscapes.

The objective of this research is to test S1 C-band SAR multitemporal data, also used in conjunction with ALOS2 L-Band SAR and S2 multispectral data, for detailed mapping of AGB at the provincial level in a Mediterranean forested landscape. The research is based on the hypotheses that S1 time series can provide biomass predictions at very high resolution, also due to the possibility of exploiting different seasonal information according to leaf presence (evergreen or deciduous species). Additionally, it has been hypothesized that biomass prediction could be improved by the integration of SAR at different frequency or with optical data. Specifically, the aims are to provide fine-scale maps of biomass for the Viterbo province in Central Italy and to improve the understanding of (i) the impact of leaf presence (deciduous or evergreen species) in S1 SAR response, (ii) the usefulness of S1 time series for accurate AGB prediction, and (iii) the advantages offered by the integration of S1 data with L-band SAR (ALOS2) or S2 multispectral data.

2.

Materials and Methods

2.1.

Study Area

Several mature forest stands were surveyed in different locations of the Viterbo province study area (Fig. 1). These forests have a high landscape conservation value and are included within the Natura 2000 sites network.

Fig. 1

The location of the surveyed forest stands within Viterbo province (yellow marks, provincial boundary in red); the blue dots represent the 34 INFC-independent sample plots. Landsat 8 real color image from Google Earth on the background.

Main forest categories according to the European Forest Type classification system⁵⁴ are Mediterranean pine forest, thermophilous deciduous forest, and mountainous beech forest. High forests (beech—Fagus sylvatica and Turkey oak—Quercus cerris) and coppice stands with standards (sweet chestnut—Castanea sativa and Turkey oak) are included. The soils are fertile, deep, and loose with acid pH, mainly classified as andisols and identified as “black soil.” The bioclimate is meso-mediterranean subhumid with a mean annual temperature of 12.8°C and annual rainfalls ranges between 1250 and 1550 mm. July is the hottest month with an average temperature of 22°C, and January is the coldest one with 4.2°C; summer drought does not usually occur due to the humid air coming from the Tyrrhenian Sea and the lakes of the area, although a subarid period between July and August may occur. Beech stands are also considered a habitat of European priority interest 9210*—Apennine beech forests with Taxus and Ilex, in accordance with the EU Habitats Directive (92/43/EEC). The only exceptions among the studied forest stands are represented by the Italian stone pine (Pinus pinea) forests located along the coastline, established from the 30s to the 50s of the last century by the State Forest Service and by the mixed forest stands located within “Villa Giustiniani-Odescalchi” in Bassano Romano, mainly composed by holly oak (Quercus ilex), sweet chestnut, and Norway spruce (Picea abies).

3.

Results

The correlation between S1 backscatter and AGB field values, in different time periods, is shown in Fig. 2 for deciduous and in Fig. 3 for evergreen plots. For evergreen plots, the correlation was always very high ($>0.75$) with minimal variations among the different time series and polarizations. Lower correlation values ($<0.7$) were found for the deciduous group, with large variations in different time periods.

Fig. 2

Pearson’s correlation coefficient calculated between S1 backscattering and AGB for the 17 deciduous plots and for different time series.

Fig. 3

Pearson’s correlation coefficient calculated between S1 backscattering and AGB for the 12 evergreen plots and for different time series.

The stepwise regression tests were conducted using AGB values transformed in natural logarithm, with results summarized in Table 1. The selected inputs were always significant ($p\text{-}\text{value}<0.05$). When the 44 S1 inputs were tested, only the “S1 VH-VV Feb-Apr” time series was selected, and the regression obtained with leave-one-out (LOO) cross validation had a coefficient of determination ($R^2$) equal to 0.55 and an RMSE equal to $126\mathrm{Mg}{\mathrm{ha}}^{-1}$. The four ALOS2 inputs were added to this S1 input, repeating the stepwise procedure with 48 inputs: the results were the selection of “S1 VH-VV Feb-Apr,” “S1 VH Apr-June,” and “ALOS2 HV-HH” inputs, and an LOO-validated $R^2$ equal to 0.67 with an RMSE of $100\mathrm{Mg}{\mathrm{ha}}^{-1}$. The inclusion of quadratic terms determined an improvement of both LOO-validated $R^2$ (equal to 0.71) and RMSE ($74.5\mathrm{Mg}{\mathrm{ha}}^{-1}$). Categorical information on leaf presence was then included but not selected as significant input at this stage.

Prediction for a smaller AGB range, arbitrarily set up to $400\mathrm{Mg}{\mathrm{ha}}^{-1}$, was also attempted, and this allowed keeping a reasonable number of plots (24), ranging from 70.4 to $393\mathrm{Mg}{\mathrm{ha}}^{-1}$, with an average AGB of $201\mathrm{Mg}{\mathrm{ha}}^{-1}$ and a standard deviation equal to $103.2\mathrm{Mg}{\mathrm{ha}}^{-1}$. When S1 inputs were tested using this reduced AGB range, the stepwise procedure resulted again in the selection of “VH-VV Feb-Apr” (as for the full set of AGB) as input with an LOO-validated $R^2$ of 0.52 and RMSE of $71\mathrm{Mg}{\mathrm{ha}}^{-1}$; adding ALOS2 data resulted also in a selection similar to the one obtained with the full AGB range, with “VH-VV Feb-Apr” and “ALOS2 HV-HH” inputs and an increase of LOO-validated $R^2$ to 0.56 and a decrease of RMSE to $68\mathrm{Mg}{\mathrm{ha}}^{-1}$. The use of quadratic terms did not improve this result, but, when the categorical information on deciduous or evergreen dominance was added, the LOO-validated $R^2$ increased to 0.7 and RMSE decreased to $46.6\mathrm{Mg}{\mathrm{ha}}^{-1}$. Figure 4 shows the predicted versus observed AGB values for this LOO regression.

Fig. 4

Scatterplot of predicted versus observed values [slope for blue evergreen (0) $\text{line}=0.9$ and slope for red deciduous (1) $\text{line}=0.76$]. The predicted AGB values are obtained using back-transformed AGB values from the following equations based on S1 and ALOS2 inputs and categorical information ($R^2=0.7$,$\mathrm{RMSE}=46.6\mathrm{Mg}/\mathrm{ha}$): evergreen (0): $\ln (\mathrm{AGB})=2.595-0.3986$ S1VH-VVFeb-Apr − 0.1848 ALOS2 HV-HH; deciduous (1): $\ln (\mathrm{AGB})=3.957-0.3986$ S1VH-VVFeb-Apr + 0.1848 ALOS2 HV-HH.

When the S2 inputs were added to those used in the previous regression test (with reduced AGB range), the stepwise procedure discarded ALOS2 and selected the “S1VH-VVFeb-Apr” from S1 and B6, B8, and B8A from S2, with the deciduous or evergreen information being not significant; similarly to the previous test, the LOO $R^2$ was equal to 0.7 and RMSE to $47\mathrm{Mg}{\mathrm{ha}}^{-1}$. Figure 5 shows the scatter plot of predicted versus observed AGB LOO values.

Fig. 5

Scatterplot of predicted versus observed values ($\text{slope}=0.77$). The predicted AGB values are obtained using back-transformed AGB values from the following equations based on S1 and S2 inputs ($R^2=0.7$$\mathrm{RMSE}=47\mathrm{Mg}/\mathrm{ha}$): $\ln (\mathrm{AGB})=3.236-0.3615$ S1 VH-VVFeb-Apr − 0.001943 S2-B6 − 0.000417 S2-B8 + 0.001988 S2-B8A.

The (f) and (g) inputs in Table 3 were considered better suited for AGB prediction, even in view of the upper limit of $400\mathrm{Mg}{\mathrm{ha}}^{-1}$ of model validity, due to lower RMSE values and the absence of quadratic forms in the regressions. These inputs were used to produce two different AGB maps for the forested areas in the Viterbo province: one being based on SAR only and the other on joint SAR and optical data (Fig. 6).

Table 3

List of regression tests, with LOO validation, conducted with different inputs and AGB ranges.

Fig. 6

AGB maps of Viterbo province.

A statistical comparison of the maps values is reported, but it should be considered just as an indication because values external to the range used for AGB regressions are not fully reliable. According to the S1-S2 map, the mean AGB in the Viterbo forests considered here (total surface equal to $678.1{\mathrm{km}}^2$) is $365.4\mathrm{Mg}{\mathrm{ha}}^{-1}$, with standard deviation of $153.2\mathrm{Mg}{\mathrm{ha}}^{-1}$, and a total AGB of 24699.6 Gg. The S1-ALOS2 map showed a mean AGB equal to $219.2\mathrm{Mg}{\mathrm{ha}}^{-1}$, with standard deviation of $113.9\mathrm{Mg}{\mathrm{ha}}^{-1}$ and total AGB of 14862.2 Gg. The frequency distribution of the AGB found in the two maps is also compared with the measurements extracted from the INFC that shows in general lower values (Fig. 7); the per-pixel Pearson’s correlation coefficient between the two maps equaled 0.36.

Fig. 7

Histogram of percentage of plots/pixels occurring in different AGB classes of the INFC data (plots, in yellow) and of the AGB maps (pixels, in red S1-ALOS2 and in green S1-S2).

The visual inspection of a map of AGB absolute values differences (Fig. 8), obtained subtracting the per-pixel values of the maps, revealed larger disagreement ($>200\mathrm{Mg}{\mathrm{ha}}^{-1}$) in areas having higher AGB density in the S1-S2 map.

Fig. 8

Map of the difference in AGB between S1-S2 and S1-ALOS2 maps.

Differences in AGB between the maps and INFC 2005 data were computed for 34 plots for S1-ALOS2 and 24 plots for S1-S2 because areas with prediction AGB $>400\mathrm{Mg}{\mathrm{ha}}^{-1}$ were excluded from this comparison. The resulting AGB differences were significant for both maps, but the distribution of the error did not show any clear trend at increasing AGB values. The histogram of the INFC 2005 data (Fig. 7) was more similar to S1-ALOS2 AGB distribution, as most values were $<200\mathrm{Mg}{\mathrm{ha}}^{-1}$. The main differences were observed for classes having low AGB ($<100\mathrm{Mg}{\mathrm{ha}}^{-1}$); those classes are less represented in the ground data that were used to train and validate the models. In general, AGB values from both maps were higher when compared with INFC 2005 ground data.

INFC estimates are not available at the provincial level but only at the regional one; the Viterbo province covers 21% of the Lazio region surface, for which the INFC reported for 2005 a total AGB equal to 46010.5 Gg, distributed in a forested surface of $5438.5{\mathrm{km}}^2$ with mean AGB equal to $84.6\mathrm{Mg}{\mathrm{ha}}^{-1}$.⁵⁷

4.

Discussion

At C-band, the contribution from leaves and the upper canopy elements tends to dominate the signal, being the most radar sensitive to features having dimension characteristics of the scale of the probing wavelength.⁶⁴ In the present study, the main contribution from crowns determined the S1 sensitivity to seasonal phenological behavior for the deciduous plots, as shown by the Pearson’s correlation values found for this group, which greatly changed according to seasons and polarizations (Fig. 2). Instead, for the evergreen group, the correlation values were always high, with minimal changes throughout the year (Fig. 3). In deciduous plots, it is reasonable to have high VH-AGB values only in the leaves-on season, as in this period the leaves’ presence contributes to crown volumetric scattering, which is missing in leaves-off conditions. The same applies to evergreen plots, as the presence of leaves throughout the year always produces high volumetric scattering. For the deciduous group, the polarization ratio showed higher scores; this ratio can be linked to the presence of small branches, which are exposed in leaf-off months and are related to higher biomass because of their abundance. Additionally, as VV backscatter is usually linked both to water content and surface roughness, the combination of VH and VV possibly reduced the influence of surface scattering and foliar water content, making the S1 signal more sensitive to AGB.

In agreement with these considerations, the “S1VH-VV Feb-Apr” input was always selected in the different regression tests (Table 3), resulting in very high scores for both deciduous and evergreen groups. The winter ratio selection confirms the S1 seasonal sensitivity for one of these groups, a fact previously observed in other research,⁴⁰ which found significant differences among the S1 signal in different seasons; also, note that deciduous forests were more affected than evergreen ones by seasonal changes.

The regression analysis in Table 3 indicates that S1 alone moderately explains the AGB variability in the study area, even with temporal time series availability. The integration of ALOS2 L-band to S1 always produced a consistent improvement resulting in increased $R^2$ and reduced RMSE with respect to S1 input alone. The use of multiband SAR information for improving AGB predictions is well documented in the literature for different forests and data types: Ranson and Sun⁶⁵ used P- or L-band data in conjunction with C-band data in a northern forest, Ferrazzoli et al.⁶⁶ tested the same bands for crop and arborous vegetation in Italy, Mohan et al.⁶⁷ used models based on multiband SAR data to improve assessment in India, and Stelmaszczuk-Gorska et al.⁶⁸ used L- and C-band data in Russian forests. Considering the limited penetration capability of S1, a benefit from the addition of L-band data was expected for providing information related to larger forest structural elements. For both SAR types, the combination of polarizations showed better results since they can be linked to biomass. This was also observed in previous research, independently by the used SAR bands: polarization ratios obtained from L-band have proved effective in subtropical and tropical forests^69,70 and ratios from C-band have been used in subtropical forests,²⁵ as well as in Mediterranean shrublands, where it proved to be less affected by topography effects.⁴⁹ However, other studies are needed to clarify the signal mechanisms that lead, in deciduous or evergreen groups, in different forest types, and in varying environmental conditions, to the use of different channels combinations.

Even if the accuracy is improving by fusing C- and L-band data, the tests carried out with the full range of field values (up to $717\mathrm{Mg}/\mathrm{ha}$) resulted in high RMSE and deviance of predicted values with respect to observed ones. Additional tests carried out using reduced calibration data (upper limit of $400\mathrm{Mg}/\mathrm{ha}$) lead to more accurate results with a consistent RMSE decrease. Two “upper-bounded” models were selected to produce the AGB Viterbo province maps, having equal prediction accuracy. In the first, based only on SAR inputs, both SAR bands were useful, and the leaf presence information was exploited; in the second, with added S2 data to SAR inputs, ALOS2 was not selected, but instead three bands from the NIR and specific red-edge spectral portion were included. The first model confirmed the usefulness of multiband SAR, while the second showed the complementarity of optical and SAR data, which has been already recognized by a range of biomass studies. Fusing S1 and S2 data, an improvement around 14% in AGB prediction in Mediterranean shrublands was obtained with respect to the usage of single sensors.⁴⁹ In other forest studies conducted in China, Italy, and Thailand, the integration of ALOS L-band and Landsat data was usefully employed for biomass assessment.^35,51,71 An improvement in accuracy of AGB predictions was also obtained using SAR in multiple bands together with very high-resolution optical images.^32,72 The S2 optical spectral region selected in the present research is linked to chlorophyll content and, thus, to both number of leaves and their photosynthetic activity and health conditions. Horler et al.⁷³ noted that the position of the red edge is affected by the number of leaves layers, which in turn can be related to canopy thickness, leaf area index, and biomass. The relevance of red-edge information for AGB prediction has been previously proved; red edge bands have been used as additional data in LIDAR-based tropical forest biomass predictions⁶¹ and for wetland biomass prediction.^74,75

The two produced AGB maps, one based on SAR data and the other on SAR plus optical data, showed reasonable agreement with each other at the per-pixel level, except in areas with high AGB values in the S1-S2 map. When considering the total AGB for the province, the prediction from S1-ALOS2 seems in line with what would be expected if the INFC regional estimates are scaled over the provincial territory and the large occurrence of mature forests in Viterbo area is taken into account. The discrepancy between the two maps can be attributed to various reasons; the most obvious is the intrinsic limits of the models, calibrated up to $400\mathrm{Mg}{\mathrm{ha}}^{-1}$ limit, with model scatter plots also showing larger uncertainties at higher AGB values.

The saturation of the SAR signal at high AGB values is likely to be responsible for underprediction of AGB in the S1-ALOS2 map. SAR saturation has been observed since the first SAR-based biomass prediction researches, with X- or C-band usually associated with saturation at much lower values with respect to other bands.^42,65,76 Overprediction of biomass when using optical data is also known to occur, as previously reported with different optical data types^77,78 and when using joint optical and microwave data,⁵¹ such as in this case.

Given the lack of additional ground truth for further validation, it is difficult to assess which of the maps better approximate the actual AGB values in the different forests of the study area, and it is likely that either overprediction or underprediction occurred. In fact, the slopes observed in Figs. 4 and 5, relating to predicted versus observed values, indicate slight underprediction (being all slopes $<1$) for both maps while the comparison with INFC-independent sample indicates general overprediction. However, this comparison is influenced by the many differences occurring between the INFC inventory data and the ground data used to generate maps, such as minimum DBH of sampled trees, data collection dates, plot size, and shape. In addition, the maps have a $400\text{-}{\mathrm{m}}^2\text{pixel}$ that do not match well with the INFC circular plot position and size ($530{\mathrm{m}}^2$), and the INFC values cannot be safely extrapolated to the larger area covered by a $3\times 3\text{pixel}$ window used to extract AGB from the maps. The INFC histogram resembles that of the S1-ALOS2 distribution, except for lower AGB classes, which are limitedly represented in the ground truth data used in this study. The scarce number of low AGB plots in the field data is possibly responsible for overprediction at low biomass ranges in both maps and reflects the general difficulty found in research studies to directly collect forest information or to get the availability of ground data from other sources (e.g., inventories). At higher biomass ranges, overprediction may occur, especially when using optical data in addition to SAR due to extrapolation in areas in which crowns show different reflectivity characteristics with respect to plots. The crown spectral characteristics are often influenced by microclimate, water conditions, or other forest health status; future work, such as introducing finer thematic information on leaf presence and forest types into the models, could clarify if this is the case. Presently, we consider that predictions based on SAR data are more conservative than those based on joint optical and SAR, which can generate—at least in this study area—overprediction in AGB values. It is worth noticing that the model based on SAR data required previous knowledge on the deciduous/evergreen dominance, while the one using S2 input did not. This fact gives an added value to S2 data and to the model based on joint SAR and S2, especially considering that this detailed forest type information, which was used here, is not always available.

5.

Conclusions

In general, radar has been less frequently used in forestry with respect to LIDAR and optical data. Sentinel-1 is now devised as an effective SAR system to improve forest vegetation remote sensing,⁷⁹ and studies exploring radar data potential for forestry applications can facilitate a wider use of SAR sensors.

Overall, this research shows the usefulness of Sentinel-1 data to map forest biomass at a spatial resolution which has rarely been achieved but that is requested for local management activities. Accurate AGB predictions were obtained up to $400\mathrm{Mg}{\mathrm{ha}}^{-1}$, which is a value that encompasses most of the forests found in the Mediterranean area. Given the lack of satellite data optimally suited for AGB mapping, the results presented here can be relevant, as they show that, with currently available free SAR data, fine-scale biomass analysis is possible.

In this research, the relatively small number of available ground data did not allow for performing AGB predictions for deciduous or evergreen dominated forests separately; this ground data scarcity is common given the resources needed for field data collection and the restriction imposed on official inventories. The number of available plots thus represents a limit in this research, and the findings reported here have to be considered as preliminary indications, to be expanded for future use of S1 data for biomass mapping purposes.

The results suggest that at C-band the availability of multitemporal information is very important for improved characterization of broadleaf forests. However, the accuracy obtained using S1 data alone was moderate, and the integration of L-band information on leaf presence proved necessary to reduce uncertainty in the AGB predictions. The potential of S1 data in predicting AGB can possibly be improved if models are developed per specific groups (evergreen or deciduous species) or per forest types. The integration of optical S2 data to S1 data showed results that could lead to overestimation; however, other efforts are needed in this respect to confirm this finding. It would be also relevant to evaluate if forest traits other than leaf presence, derived by S2 data, can be useful for improving AGB prediction.

An indication about the optimal periods of satellite data acquisition can also be derived from this research. The time period of late winter and beginning of spring is suggested in the case of SAR data, when the deciduous trees are still leafless and the signal from branches is more evident. Even if this study did not test optical time series, for this data type, the main acquisition issue is related to cloud or haze presence, which even at these latitudes can be consistent in forested areas; the late spring and beginning of summer period, before the leaves dry and start senescence phase, is, therefore, indicated for S2 images.

In addition, this research evidenced, on one hand, the lack of data and the high uncertainty in AGB estimates at the provincial level, where existing maps and inventory data do not provide sufficient information. On the other hand, the limited sensitivity of currently available satellite data for AGB prediction is evident, considering that the best models were those calibrated with an upper AGB bound of $400\mathrm{Mg}{\mathrm{ha}}^{-1}$. While waiting for future sensors better suited for forest studies, biomass data can be delivered at fine scale using multiband SAR sensors, as this research showed. Considering that forest areas with very high carbon density are not so diffuse in this region and that for applied purposes it is preferable to maintain as minimum as possible the deviance of predictions, the presented models can be of practical use for analyzing in detail the spatial distribution of biomass in fragmented landscapes of moderate biomass density.

A full open-access data policy, such as the one adopted for Sentinels or Landsat, can favor the integration of optical or multifrequency data to S1 and is urgently needed for other SAR missions to support the full exploitation of SAR potential for forest mapping and inventory. For comparison with inventory data, the collaboration with the National Forest Service allowed the current analysis to be conducted through matching between plots and pixels from the maps created by service staff. However, exact geolocations of plots are not available for security and plot protection reasons; this means that without the support of the National Forest Service this procedure cannot be replicated. We wish that a compromise between data protection and research needs will quickly be found, as well as updating data with more recent inventory information, to help the development of new products based on remote sensing that could also support future field activities and inventory revisits.