|
1.INTRODUCTIONOne prominent example of the benefits of microgravity is atom interferometry. Whereas in gravitational platforms, atoms simply drop out of the experiment frame for too long free evolution times, this limitation does not hold for microgravity platforms. Typically, the resolution of an atom interferometer scales quadratically with the free evolution time, such that this is a major advantage. There are a great number of different microgravity platforms.1 While a drop-tower offers good microgravity conditions, the number of experimental cycles that can be run on a given day are usually very limited. Furthermore, the time of one experimental cycle is limited to the range of 10 s.2 Parabolic Flights are limited by the microgravity quality. Sounding Rockets offer a long continuous experimental time, but usually only for one experimental cycle. Compared to previously mentioned platforms, a satellite or space-station offers excellent microgravity conditions, and quasi-continuous operation, enabling many long experimental cycles. The DLR-NASA Bose-Einstein Condensate and Cold Atom Laboratory (BECCAL) mission is a multi-user facility that will enable quantum optical experiments with different isotopes of rubidium and potassium like atom interferometry aboard the ISS,3 and a direct successor to NASA’s CAL mission.4–6 However, this platform comes with several constraints. Firstly, the payload, including optical benches, needs to withstand the mechanical loads during launch. Once placed in the foreseen express rack locker, the experiment needs to run without external maintenance for a timescale of a few years in varying temperature conditions. This is in stark contrast to most lab-based setups, where frequent readjustment of the optics is needed. Furthermore, the payload needs to accommodate most optics used for light distribution that are also found in a lab in a ground-based setup while adhering to the limited weight and size budget of such a mission. To match these requirements, we make use of our miniaturized optical toolkit specifically designed for such use-cases. The toolkit is based on the glass ceramic Zerodur, which has a negligible coefficient of thermal expansion of ±0.007 × 10–6/K7 and mechanical properties akin to aluminium.8 Using adhesives with different curing conditions, miniaturized optical components are glued onto an optical bench made from Zerodur. This enables long processing and short curing times,9 as well as the manufacture of composite components such as fiber couplers and collimators, as compared to bonding methods such as hydroxide-catalysis bonding.10 During assembly, components are placed successively such that misalignments from the previous component can be compensated by the following component. The toolkit has been applied in previous sounding rocket missions: FOKUS (first launched on 2015-04-23),11 KALEXUS (launched on 2016-01-23),12 MAIUS-1 (launched on 2017-01-23)13, 14 and the upcoming MAIUS-2/3 missions.15 2.OPTICAL BENCHES FOR BECCALThe overall system concept and scientific scope for the BECCAL mission has previously been outlined.3 As a multi-user experimental platform, it will enable a wide range of scientific experiments in the fields of atom interferometry, coherent atom optics, the study of ensembles of scalar and spinor Bose-Einstein particles, quantum gas mixtures, as well as strongly interacting gases and molecules, and may serve as a demonstrator for quantum information applications. Compared to previous sounding rocket and satellite missions, an even more functionally complex experimental apparatus is needed to enable this complex scientific scope, which is especially evident in the number and frequencies of light-fields required: In addition to the light-fields close to atomic resonance used to cool, trap, manipulate and image the atoms, there will be a crossed, red-detuned optical dipole trap at 1064nm, arbitrarily painted, blue-detuned potentials at 764nm, as well beams for Raman atom interferometry along two separate axes. As part of the BECCAL payload, we will produce eight optical benches in total for light intensity control and distribution, as well as two optical benches for frequency stabilization. The optical benches, as well as their mounting are shown in Fig. 1. The optical benches used in BECCAL are fiber-coupled, which means they receive light from an optical fiber, which is collimated to free-space using a collimator and then return it to an optical fiber using an optical coupler. In between, a variety of components are used for light manipulation, such as waveplates, polarization beam splitters (PBS) and dichroic mirrors to overlap and split light fields, and acousto-optic modulators (AOM) and shutters for intensity control. We use static and adjustable mirrors to guide the light from one component to the next. Unlike static mirrors, the pointing of adjustable mirrors can be adjusted after assembly of an optical bench, but will be locked into place before launch of the payload. In contrast to previous sounding rocket missions, we have made some adaptions: To further reduce the form-factor of the optical benches, we mount optical components on both sides of the Zerodur benches. Static mirrors are used to guide light through holes in the optical bench onto the other side. The mounting of the optical benches has also been updated. Previously, optical benches were screwed onto a metal plate with a layer of rubber in-between. For the distribution benches in BECCAL, this is no longer an option as the benches are double-sided. Hence, they are held in place by an aluminium frame that grabs onto the edges of the bench from all sides. A thin rubber layer in-between frame and bench cushions the optical benches by ensuring that the loads from the holder are distributed evenly. This has the advantage that deformations due to local mounting forces are suppressed. Further, in this drawer-like design, all fibers enter and exit the optical bench on one side. This facilitates fiber guiding and enhances modularity. Lastly, we have expanded the toolkit to new wavelengths such as 764nm and 1064nm. 3.SCIENTIFIC DEMONSTRATORS3.1Optical bench demonstratorTo verify the functionality of our optical bench system, we have constructed a scientific demonstrator for the 1064nm optical bench used to prepare the light fields for the optical dipole traps. The corresponding early layout of the optical bench for 1064nm is shown in Fig. 2a. As on all optical benches, light is collimated from an optical fiber using a collimator. To avoid back-reflections, the light will first pass an optical isolator. For this particular bench, due to lack of availability of small form factor optical isolators at 1064nm with a high transmission, we use a conjunction of two commercial optical faraday rotators for 780nm to achieve a rotation of 45 deg. For all other wavelengths, we can use a single optical isolator. We use a PBS to separate the light field into two for use in a crossed dipole trap. Independent intensity control of each of the light fields is performed by using AOMs in 1st order for fast intensity control, and optical shutters for complete extinction. Both light fields are then coupled back into two separate fibers. A photograph of the demonstrator, including mounting can be seen in Fig. 2b. To test if the optical bench, including mounting structure, could withstand the rocket launch, a vibration test along three axes was performed, including random vibrations at an exaggerated qualification level of more than 11gRMS and a half-sine shock for each axis. To assure that the benches retain their optical performance after the launch, the ratio of output to input power for each of the fibered outputs was recorded before and after each test. Bench and mounting structure performed well, without variations of power before and after the test of more than 10%. We attribute the majority of the variations present to a sub-optimal attachment of optical fiber to ferrule, causing a variable bend in the fiber during the vibration tests. As for the final flight model, commercial fibers will be used, this is of no concern. 3.2Thermal optimization and testsSounding rocket missions typically have a duration of only some minutes, such that any thermal heat-up during operation of the payload is usually uncritical. The continuous operation of the BECCAL payload imposes new challenges on thermal management. As Zerodur is a poor thermal conductor, we try to carefully limit the amount of heat generated by elements mounted on the optical benches. The two main heat sources are the motor used to actuate the optical shutter blades, as well as the acousto-optic modulators. To evaluate how the operation of the AOMs affects the temperature of the optical benches, thermal tests on the demonstrator have been performed. To limit the effect of convection, the setup was put in an acrylic glass case. The AOMs were then switched on and the temperature monitored. The setup is shown in Fig. 3a, with the front acrylic glass wall removed for better visibility. Fig. 3b shows the temperature evolution of the AOMs: At a power of 1.2W, which corresponds to the optimum operating power for AOMs at 780nm and ambient temperature of 21 °C, both AOMs heated up by roughly 14 K. We are currently performing thermal tests at different operation parameters. 3.3Mechanical ShuttersFor previous sounding rocket missions, stepper motors were used to actuate an opaque blade between two states, one blocking the optical beam, and one letting it pass (see Fig. 4a and b). Most stepper motors, however, require constant power to maintain their position, and thus act as a continuous heat source. Thermal simulations show that stepper motors are thus unsuitable for our experiment, as they produce too much heat. Instead, for BECCAL, we plan to use bi-stable rotational solenoids. These only require power to switch between their two stable rotational states, thus greatly reducing thermal loads. We are currently testing solenoids from different companies for their suitability. Likely the most important test performed is a test of the response time. Fig. 4c shows the recorded response times for one of the solenoids. The switching time (time between 10% and 90% extinction) below 1 ms is well sufficient for our purposes, especially since the shutters are always used in conjunction with AOMs for fast extinction. Solenoids from different companies show similarly quick response times. Note that this is only one of many tests: Next to verifying general electric and physical compatibility, we are currently finalizing an array of tests, such as a determination of detent and holding torque, vibrational tests to see if solenoid and blade can withstand the vibrations during launch, and extended life-time tests. 3.4Spectroscopy DemonstratorTo enable the broad scientific scope of BECCAL, we need precise and flexible frequency control of the scientific light fields, as well as a stable frequency reference. To this end, two spectroscopic benches will be used to enable the stabilization of one master laser each for rubidium and potassium to relevant transitions. The scientific lasers can then be stabilized relative to these transitions via an offset-lock. A demonstrator of the spectroscopic setup was constructed, which is shown in Fig. 5a. A fiber-optic EOM is used to modulate one of the beams leading to the spectroscopic bench. Both modulated (blue) and unmodulated beam (red) enter the optical bench through separate collimators with perpendicular linear polarization. They then pass two spectroscopic cells filled with the relevant atoms. As the polarization of each beam is rotated by 90 deg between the cells, polarization beam splitters can be used to split off the respective beam to be redirected onto a photodiode. As both modulated and unmodulated beams are recorded and demodulated, this setup enables simultaneous frequency modulation (FMS) and modulation transfer spectroscopy (MTS), which in return enables a stable lock to multiple transitions for each atom.16, 17 To characterize the spectroscopic setup, we simultaneously recorded FMS- and MTS-signals for various optical and electrical settings. The photodiode PCBs used to record the signals, which are normally glued to the side of the optical benches, were mounted off-image for easy adaption of the electrical parameters. One set of spectroscopic signals is shown in Fig. 5b, including error signal slopes and noise levels of the most dominant transitions. Judging by these parameters, a short-time absolute frequency stability in the sub-MHz-range should be achievable. 4.CONCLUSIONThe DLR-NASA BECCAL project requires an optical distribution system that is both small and lightweight and which can withstand the mechanical loads during launch and temperature fluctuations during operation, and remain optically stable for a period of multiple years. In this publication, we have demonstrated how we have adapted and expanded our Zerodur-based optical bench toolkit, which is ideally suited for these environments, for this purpose. The most prominent adaption is the use of double-sided mounting of optical components, leading to further miniaturization, as well as a new mounting strategy. Ten optical benches, eight for light control and distribution, and two as a spectroscopic reference will be part of the BECCAL payload. Tests have been performed on a number of technical demonstrators to assess the feasibility of the adaptions: A technical demonstrator of a double-sided optical bench including mounting was constructed to test the thermal behaviour and mechanical stability, and performed well during a vibrational test. Using the same toolkit, a spectroscopic bench has been produced to successfully perform simultaneous FMS and MTS spectroscopy to enable frequency stabilization to a broad range of optical transitions. Further, to reduce thermal loads, we aim to use rotary solenoids instead of steppers motors to actuate shutter blades. Solenoids from various companies are currently undergoing rigorous qualification testing. With these advancements, the toolkit will help enable the broad scientific scope of the BECCAL mission. AppendicesAPPENDIX A.ACKNOWLEDGEMENTSOur work is supported by the German Space Agency DLR with funds provided by the Federal Ministry for Economic Affairs and Energy (BMWi) under grant number 50 WP 1433, 50 WP 1703 and 50 WP 2103. Special thanks to Klaus Sengstock from the University of Hamburg for supporting the development of the Zerodur Technology. REFERENCESThomas, V. A., Prasad, N. S., and Reddy, C. A. M.,
“Microgravity research platforms – A study,”
Current Science, 79
(3), 336
–340 Google Scholar
“Bremen Drop Tower - Payload User’s Guide - Version 1.1,”
(2022). Google Scholar
Frye, K., Abend, S., Bartosch, W., Bawamia, A., Becker, D., Blume, H., Braxmaier, C., Chiow, S. W., Efremov, M. A., Ertmer, W., Fierlinger, P., Franz, T., Gaaloul, N., Grosse, J., Grzeschik, C., Hellmig, O., Henderson, V. A., Herr, W., Israelsson, U., Kohel, J., Krutzik, M., Kürbis, C., Lämmerzahl, C., List, M., Lüdtke, D., Lundblad, N., Marburger, J. P., Meister, M., Mihm, M., Müller, H., Müntinga, H., Nepal, A. M., Oberschulte, T., Papakonstantinou, A., Perovšek, J., Peters, A., Prat, A., Rasel, E. M., Roura, A., Sbroscia, M., Schleich, W. P., Schubert, C., Seidel, S. T., Sommer, J., Spindeldreier, C., Stamper-Kurn, D., Stuhl, B. K., Warner, M., Wendrich, T., Wenzlawski, A., Wicht, A., Windpassinger, P., Yu, N., and Wörner, L.,
“The Bose-Einstein Condensate and Cold Atom Laboratory,”
EPJ Quantum Technology, 8
(1), 1
–38 https://doi.org/10.1140/epjqt/s40507-020-00090-8 Google Scholar
Elliott, E. R., Krutzik, M. C., Williams, J. R., Thompson, R. J., and Aveline, D. C.,
“NASA’s cold atom lab (CAL): system development and ground test status,”
npj Microgravity, 4
(1), 1
–7 Google Scholar
Aveline, D. C., Williams, J. R., Elliott, E. R., Dutenhoffer, C., Kellogg, J. R., Kohel, J. M., Lay, N. E., Oudrhiri, K., Shotwell, R. F., Yu, N., and Thompson, R. J.,
“Observation of Bose–Einstein condensates in an Earth-orbiting research lab,”
Nature, 582
(7811), 193
–197 https://doi.org/10.1038/s41586-020-2346-1 Google Scholar
“Cold Atom Lab (CAL): Quantum Technologies Take Flight.,”
https://science.nasa.gov/technology/technology-highlights/quantum-technologies-take-flight Google Scholar
“SCHOTT Technical Information TIE-43: Properties of Zerodur,”
(2014). Google Scholar
“TIE-33 bending strength of optical glass and ZERODUR,”
(17), Google Scholar
Duncker, H., Hellmig, O., Wenzlawski, A., Grote, A., Rafipoor, A. J., Rafipoor, M., Sengstock, K., and Windpassinger, P.,
“Ultrastable, Zerodur-based optical benches for quantum gas experiments,”
Applied Optics, 53
(20), 4468 https://doi.org/10.1364/AO.53.004468 Google Scholar
Elliffe, E. J., Bogenstahl, J., Deshpande, A., Hough, J., Killow, C., Reid, S., Robertson, D., Rowan, S., Ward, H., and Cagnoli, G.,
“Hydroxide-catalysis bonding for stable optical systems for space,”
Classical and Quantum Gravity, 22
(10), https://doi.org/10.1088/0264-9381/22/10/018 Google Scholar
Lezius, M., Wilken, T., Deutsch, C., Giunta, M., Mandel, O., Thaller, A., Schkolnik, V., Schiemangk, M., Dinkelaker, A., Kohfeldt, A., Wicht, A., Krutzik, M., Peters, A., Hellmig, O., Duncker, H., Sengstock, K., Windpassinger, P., Lampmann, K., Hülsing, T., Hänsch, T. W., and Holzwarth, R.,
“Space-borne frequency comb metrology,”
Optica, 3
(12), 1381 https://doi.org/10.1364/OPTICA.3.001381 Google Scholar
Dinkelaker, A. N., Schiemangk, M., Schkolnik, V., Kenyon, A., Lampmann, K., Wenzlawski, A., Windpassinger, P., Hellmig, O., Wendrich, T., Rasel, E. M., Giunta, M., Deutsch, C., Kürbis, C., Smol, R., Wicht, A., Krutzik, M., and Peters, A.,
“Autonomous frequency stabilization of two extended-cavity diode lasers at the potassium wavelength on a sounding rocket,”
Applied Optics, 56
(5), 1388 https://doi.org/10.1364/AO.56.001388 Google Scholar
Schkolnik, V., Hellmig, O., Wenzlawski, A., Grosse, J., Kohfeldt, A., Döringshoff, K., Wicht, A., Wind-passinger, P., Sengstock, K., Braxmaier, C., Krutzik, M., and Peters, A.,
“A compact and robust diode laser system for atom interferometry on a sounding rocket,”
Applied Physics B, 122
(8), https://doi.org/10.1007/s00340-016-6490-0 Google Scholar
Becker, D., Lachmann, M. D., Seidel, S. T., Ahlers, H., Dinkelaker, A. N., Grosse, J., Hellmig, O., Müntinga, H., Schkolnik, V., Wendrich, T., Wenzlawski, A., Weps, B., Corgier, R., Franz, T., Gaaloul, N., Herr, W., Lüdtke, D., Popp, M., Amri, S., Duncker, H., Erbe, M., Kohfeldt, A., Kubelka-Lange, A., Braxmaier, C., Charron, E., Ertmer, W., Krutzik, M., Lämmerzahl, C., Peters, A., Schleich, W. P., Sengstock, K., Walser, R., Wicht, A., Windpassinger, P., and Rasel, E. M.,
“Space-borne Bose–Einstein condensation for precision interferometry,”
Nature, 562
(7727), 391
–395 https://doi.org/10.1038/s41586-018-0605-1 Google Scholar
Elsen, M., Grosse, J., Rasel, E., Braxmaier, C., and MAIUS, T.,
“The Pathway to Launch the MAIUS-2/3 Payload on a Sounding Rocket,”
International Astronautical Congress,
(2019). Google Scholar
Noh, H.-R., Park, S. E., Li, L. Z., Park, J.-D., and Cho, C.-H.,
“Modulation transfer spectroscopy for 87Rb atoms: theory and experiment,”
Optics Express, 19
(23), 23444
–23452 https://doi.org/10.1364/OE.19.023444 Google Scholar
Mudarikwa, L., Pahwa, K., and Goldwin, J.,
“Sub-Doppler modulation spectroscopy of potassium for laser stabilization,”
Journal of Physics B: Atomic, Molecular and Optical Physics, 45
(6), https://doi.org/10.1088/0953-4075/45/6/065002 Google Scholar
|